Global

Global - English

Asia

Europe

Oceania

ANZ - English

Latin America

North America

Middle East and Africa

DS-3E1310P-SI

8 Port Fast Ethernet Smart POE Switch

8 × 100 Mbps PoE RJ45 port, 2 × gigabit combo.
IEEE 802.3at/af standard for PoE ports.
Network topology management, alarm push, network health monitor.
6 KV surge protection for PoE ports.
AF/AT camera can reach up to 300 m in extend mode.

View Less

Available models:

DS-3E1310P-SI

Allgemein
ShellMetal material
Nettogewicht1.72 kg (3.79 lb)
Bruttogewicht2.20 kg (4.85 lb)
Abmessungen (B × H × T)266.00 mm × 44.50 mm × 220.80 mm (10.47'' × 1.75'' × 8.69'')
Betriebstemperatur0 °C to 45 °C (0 °F to 113 °F)
Lagertemperatur-40 °C to 85 °C (-40 °F to 185 °F)
Luftfeuchtigkeit im Betrieb5% to 95% (no condensation)
Relative Luftfeuchtigkeit5% to 95% (no condensation)
Spannungsversorgung100-240 VAC, 50/60 Hz, Max. 1.5 A
InstallationsmodusRack (equipped with mounting ears)
Max. Energieverbrauch150 W
Stromverbrauch im Leerlauf5 W
Surge Protection6 KV

Netzwerk Parameter
Häfen8 × 10/100 Mbps PoE port,2 × Gigabit combo
MAC-Adresstabelle16 K
Schaltleistung9.2 Gbps
Paketweiterleitungsrate6.84 Mpps
Interner Cache4 Mbits

PoE-Netzteil
PoE-StandardIEEE 802.3af,IEEE 802.3at
PoE-Power Pin8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE-PortPoE: Ports 1 to 8
Max. Port Power30 W
PoE-Power Budget125 W

Softwarefunktion
Große ReichweitePorts 1 to 8: up to 300 m. Long range performance may vary depend on camera model or cable condition.
Port IsolationPorts 1 to 8: port isolation mode to improve network security. Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
VIP Port/
PoE-WatchdogPorts 1 to 8: auto detect and restart the cameras that do not respond.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
Link Aggregation/
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support SNMP v1/v2c for third-party management platform access. Support port mirroring for fault locating.
Storm ControlStorm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Supports port rate limiting based on broadcast, multicast, and unknown unicast packets.
DHCP SnoopingDHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through Off by default.
Port Rate-Limiting/
IGMP Snooping/
ACL/
IPSG/

Genehmigung
EMVFCC (47 CFR Part 15, Subpart B); CE-EMC (EN 55032: 2015, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011 +A1: 2014, EN 55035: 2017); IC (ICES-003: Issue 6); RCM (ASNZS CISPR 32: 2015)
SicherheitUL (UL 60950-1); CB (IEC 60950-1:2005, AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition); CE-LVD (EN 60950-1: 2006 + A11: 2009 +A1: 2010+A12: 2011+A2: 2013, EN 62368-1: 2014+A11: 2017)
ChemieCE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)

Spezifikation

Allgemein

Shell

Metal material

Nettogewicht

1.72 kg (3.79 lb)

Bruttogewicht

2.20 kg (4.85 lb)

Abmessungen (B × H × T)

266.00 mm × 44.50 mm × 220.80 mm (10.47'' × 1.75'' × 8.69'')

Betriebstemperatur

0 °C to 45 °C (0 °F to 113 °F)

Lagertemperatur

-40 °C to 85 °C (-40 °F to 185 °F)

Luftfeuchtigkeit im Betrieb

5% to 95% (no condensation)

Relative Luftfeuchtigkeit

5% to 95% (no condensation)

Spannungsversorgung

100-240 VAC, 50/60 Hz, Max. 1.5 A

Installationsmodus

Rack (equipped with mounting ears)

Max. Energieverbrauch

150 W

Stromverbrauch im Leerlauf

5 W

Surge Protection

6 KV

Netzwerk Parameter

Häfen

8 × 10/100 Mbps PoE port,2 × Gigabit combo

MAC-Adresstabelle

16 K

Schaltleistung

9.2 Gbps

Paketweiterleitungsrate

6.84 Mpps

Interner Cache

4 Mbits

PoE-Netzteil

PoE-Standard

IEEE 802.3af,IEEE 802.3at

PoE-Power Pin

8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)

PoE-Port

PoE: Ports 1 to 8

Max. Port Power

30 W

PoE-Power Budget

125 W

Softwarefunktion

Große Reichweite

Ports 1 to 8: up to 300 m. Long range performance may vary depend on camera model or cable condition.

Port Isolation

Ports 1 to 8: port isolation mode to improve network security. Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.

VIP Port

PoE-Watchdog

Ports 1 to 8: auto detect and restart the cameras that do not respond.

QoS

QoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.

Link Aggregation

Loop Prevention

Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.

VLAN

VLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.

HPP

Support one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.

System Maintenance

Support device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support SNMP v1/v2c for third-party management platform access. Support port mirroring for fault locating.

Storm Control

Storm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Supports port rate limiting based on broadcast, multicast, and unknown unicast packets.

DHCP Snooping

DHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through Off by default.

Port Rate-Limiting

IGMP Snooping

ACL

IPSG

Genehmigung

EMV

FCC (47 CFR Part 15, Subpart B); CE-EMC (EN 55032: 2015, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011 +A1: 2014, EN 55035: 2017); IC (ICES-003: Issue 6); RCM (ASNZS CISPR 32: 2015)

Sicherheit

UL (UL 60950-1); CB (IEC 60950-1:2005, AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition); CE-LVD (EN 60950-1: 2006 + A11: 2009 +A1: 2010+A12: 2011+A2: 2013, EN 62368-1: 2014+A11: 2017)

Chemie

CE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)

Allgemein

ShellMetal material
Nettogewicht1.72 kg (3.79 lb)
Bruttogewicht2.20 kg (4.85 lb)
Abmessungen (B × H × T)266.00 mm × 44.50 mm × 220.80 mm (10.47'' × 1.75'' × 8.69'')
Betriebstemperatur0 °C to 45 °C (0 °F to 113 °F)
Lagertemperatur-40 °C to 85 °C (-40 °F to 185 °F)
Luftfeuchtigkeit im Betrieb5% to 95% (no condensation)
Relative Luftfeuchtigkeit5% to 95% (no condensation)
Spannungsversorgung100-240 VAC, 50/60 Hz, Max. 1.5 A
InstallationsmodusRack (equipped with mounting ears)
Max. Energieverbrauch150 W
Stromverbrauch im Leerlauf5 W
Surge Protection6 KV

Netzwerk Parameter

Häfen8 × 10/100 Mbps PoE port,2 × Gigabit combo
MAC-Adresstabelle16 K
Schaltleistung9.2 Gbps
Paketweiterleitungsrate6.84 Mpps
Interner Cache4 Mbits

PoE-Netzteil

PoE-StandardIEEE 802.3af,IEEE 802.3at
PoE-Power Pin8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE-PortPoE: Ports 1 to 8
Max. Port Power30 W
PoE-Power Budget125 W

Softwarefunktion

Große ReichweitePorts 1 to 8: up to 300 m. Long range performance may vary depend on camera model or cable condition.
Port IsolationPorts 1 to 8: port isolation mode to improve network security. Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
VIP Port/
PoE-WatchdogPorts 1 to 8: auto detect and restart the cameras that do not respond.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
Link Aggregation/
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support SNMP v1/v2c for third-party management platform access. Support port mirroring for fault locating.
Storm ControlStorm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Supports port rate limiting based on broadcast, multicast, and unknown unicast packets.
DHCP SnoopingDHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through Off by default.
Port Rate-Limiting/
IGMP Snooping/
ACL/
IPSG/

Genehmigung

EMVFCC (47 CFR Part 15, Subpart B); CE-EMC (EN 55032: 2015, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011 +A1: 2014, EN 55035: 2017); IC (ICES-003: Issue 6); RCM (ASNZS CISPR 32: 2015)
SicherheitUL (UL 60950-1); CB (IEC 60950-1:2005, AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition); CE-LVD (EN 60950-1: 2006 + A11: 2009 +A1: 2010+A12: 2011+A2: 2013, EN 62368-1: 2014+A11: 2017)
ChemieCE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)