Commercial Display

Global

Global - English

Asia

Europe

Oceania

ANZ - English

Latin America

North America

Middle East and Africa

4 Port Fast Ethernet Smart Harsh POE Switch

Visualized topology management.
Network health monitor.
Layer 2 features: PoE watchdog, STP/RSTP, VLAN, SNMP, QoS, ERPS, etc.
-30 °C to 65 °C wide temperature range in harsh environment.

View Less

Data Sheet

Available models:

DS-3T1306P-SI/HS

Spezifikation
Resources
Zubehör

Data Sheet

Allgemein
ShellMetal material
Nettogewicht0.4 kg (0.8 lb)
Bruttogewicht1.0 kg (2.2 lb)
Abmessungen (B × H × T)158.00 mm × 101.20 mm × 31.60 mm (6.20'' × 3.90'' × 1.20'')
Betriebstemperatur-30 °C to 65 °C (-22 °F to 149 °F)
Lagertemperatur-40 °C to 85 °C (-40 °F to 185 °F)
Luftfeuchtigkeit im Betrieb5% to 95% (no condensation)
Relative Luftfeuchtigkeit5% to 95% (no condensation)
Spannungsversorgung48VDC, 1.36A
InstallationsmodusDesk-Mounted,Rail
Max. Energieverbrauch65 W
Stromverbrauch im Leerlauf5 W
Surge Protection6 kV

Netzwerk Parameter
Häfen4 × 10/100 Mbps PoE port,1 × Gigabit RJ45 port,1 × Gigabit fiber optical port
MAC-Adresstabelle2 K
SchaltleistungWhole-Device Performance: 14 Gbps Port Performance: 4.8 Gbps
PaketweiterleitungsrateWhole-Device Performance: 10.42 Mpps Port Performance: 3.57 Mpps
Interner Cache1 Mbits

PoE-Netzteil
PoE-StandardIEEE 802.3af,IEEE 802.3at
PoE-Power Pin8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE-PortPoE: Ports 1 to 4
Max. Port Power30 W
PoE-Power Budget60 W

Softwarefunktion
Große ReichweitePorts 1 to 4: up to 300 m. Long range performance may vary depend on camera model or cable condition.
Port IsolationPorts 1 to 4: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
PoE-WatchdogPorts 1 to 4: auto detect and restart the cameras that do not respond.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support port mirroring for fault locating.
Port Rate-Limiting Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.
Storm ControlStorm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Support port rate limiting based on broadcast, multicast, and unknown unicast packets.
DHCP SnoopingDHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through. Disabled by default.

Genehmigung
EMVCE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020)
SicherheitCB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition), CE-LVD (EN 62368-1: 2014+A11: 2017)
ChemieCE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)

Allgemein

Shell

Metal material

Nettogewicht

0.4 kg (0.8 lb)

Bruttogewicht

1.0 kg (2.2 lb)

Abmessungen (B × H × T)

158.00 mm × 101.20 mm × 31.60 mm (6.20'' × 3.90'' × 1.20'')

Betriebstemperatur

-30 °C to 65 °C (-22 °F to 149 °F)

Lagertemperatur

-40 °C to 85 °C (-40 °F to 185 °F)

Luftfeuchtigkeit im Betrieb

5% to 95% (no condensation)

Relative Luftfeuchtigkeit

5% to 95% (no condensation)

Spannungsversorgung

48VDC, 1.36A

Installationsmodus

Desk-Mounted,Rail

Max. Energieverbrauch

65 W

Stromverbrauch im Leerlauf

5 W

Surge Protection

6 kV

Netzwerk Parameter

Häfen

4 × 10/100 Mbps PoE port,1 × Gigabit RJ45 port,1 × Gigabit fiber optical port

MAC-Adresstabelle

2 K

Schaltleistung

Whole-Device Performance: 14 Gbps Port Performance: 4.8 Gbps

Paketweiterleitungsrate

Whole-Device Performance: 10.42 Mpps Port Performance: 3.57 Mpps

Interner Cache

1 Mbits

PoE-Netzteil

PoE-Standard

IEEE 802.3af,IEEE 802.3at

PoE-Power Pin

8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)

PoE-Port

PoE: Ports 1 to 4

Max. Port Power

30 W

PoE-Power Budget

60 W

Softwarefunktion

Große Reichweite

Ports 1 to 4: up to 300 m. Long range performance may vary depend on camera model or cable condition.

Port Isolation

Ports 1 to 4: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.

PoE-Watchdog

Ports 1 to 4: auto detect and restart the cameras that do not respond.

QoS

QoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.

VLAN

VLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.

HPP

Support one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.

Loop Prevention

Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.

System Maintenance

Support device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support port mirroring for fault locating.

Port Rate-Limiting

Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.

Storm Control

Storm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Support port rate limiting based on broadcast, multicast, and unknown unicast packets.

DHCP Snooping

DHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through. Disabled by default.

Genehmigung

EMV

CE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020)

Sicherheit

CB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition), CE-LVD (EN 62368-1: 2014+A11: 2017)

Chemie

CE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)

Allgemein

ShellMetal material
Nettogewicht0.4 kg (0.8 lb)
Bruttogewicht1.0 kg (2.2 lb)
Abmessungen (B × H × T)158.00 mm × 101.20 mm × 31.60 mm (6.20'' × 3.90'' × 1.20'')
Betriebstemperatur-30 °C to 65 °C (-22 °F to 149 °F)
Lagertemperatur-40 °C to 85 °C (-40 °F to 185 °F)
Luftfeuchtigkeit im Betrieb5% to 95% (no condensation)
Relative Luftfeuchtigkeit5% to 95% (no condensation)
Spannungsversorgung48VDC, 1.36A
InstallationsmodusDesk-Mounted,Rail
Max. Energieverbrauch65 W
Stromverbrauch im Leerlauf5 W
Surge Protection6 kV

Netzwerk Parameter

Häfen4 × 10/100 Mbps PoE port,1 × Gigabit RJ45 port,1 × Gigabit fiber optical port
MAC-Adresstabelle2 K
SchaltleistungWhole-Device Performance: 14 Gbps Port Performance: 4.8 Gbps
PaketweiterleitungsrateWhole-Device Performance: 10.42 Mpps Port Performance: 3.57 Mpps
Interner Cache1 Mbits

PoE-Netzteil

PoE-StandardIEEE 802.3af,IEEE 802.3at
PoE-Power Pin8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE-PortPoE: Ports 1 to 4
Max. Port Power30 W
PoE-Power Budget60 W

Softwarefunktion

Große ReichweitePorts 1 to 4: up to 300 m. Long range performance may vary depend on camera model or cable condition.
Port IsolationPorts 1 to 4: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
PoE-WatchdogPorts 1 to 4: auto detect and restart the cameras that do not respond.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support port mirroring for fault locating.
Port Rate-Limiting Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.
Storm ControlStorm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Support port rate limiting based on broadcast, multicast, and unknown unicast packets.
DHCP SnoopingDHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through. Disabled by default.

Genehmigung

EMVCE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020)
SicherheitCB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition), CE-LVD (EN 62368-1: 2014+A11: 2017)
ChemieCE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)