Global

Global - English

Asia

Europe

Oceania

ANZ - English

Latin America

North America

Middle East and Africa

4 Port Fast Ethernet Smart Harsh POE Switch

Visualized topology management.
Network health monitor.
Layer 2 features: PoE watchdog, STP/RSTP, VLAN, SNMP, QoS, ERPS, etc.
-30 °C to 65 °C wide temperature range in harsh environment.

View Less

Data Sheet

Available models:

DS-3T1306P-SI/HS

Especificación
Resources
Accesorios

Data Sheet

General
CarcasaMetal material
Peso neto0.4 kg (0.8 lb)
Peso bruto1.0 kg (2.2 lb)
Dimensiones (W x H x D)158.00 mm × 101.20 mm × 31.60 mm (6.20'' × 3.90'' × 1.20'')
Temperatura de funcionamiento-30 °C to 65 °C (-22 °F to 149 °F)
Temperatura de almacenamiento-40 °C to 85 °C (-40 °F to 185 °F)
Condiciones de humedad5% to 95% (no condensation)
Humedad relativa5% to 95% (no condensation)
Fuente de alimentación48VDC, 1.36A
Modo de instalaciónDesk-Mounted,Rail
Max. El consumo de energía65 W
Consumo de energía en inactivo5 W
Surge Protection6 kV

Parámetros de red
Puertos4 × 10/100 Mbps PoE port,1 × Gigabit RJ45 port,1 × Gigabit fiber optical port
Tabla de direcciones MAC2 K
Capacidad de conmutaciónWhole-Device Performance: 14 Gbps Port Performance: 4.8 Gbps
Tasa de reenvío de paquetesWhole-Device Performance: 10.42 Mpps Port Performance: 3.57 Mpps
Caché interna1 Mbits

Fuente de alimentación PoE
PoE StandardIEEE 802.3af,IEEE 802.3at
Pin de alimentación PoE8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
Puerto PoEPoE: Ports 1 to 4
Max. Puerto de alimentación30 W
PoE Power Budget60 W

Función de software
Largo alcancePorts 1 to 4: up to 300 m. Long range performance may vary depend on camera model or cable condition.
Port IsolationPorts 1 to 4: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
PoE WatchdogPorts 1 to 4: auto detect and restart the cameras that do not respond.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support port mirroring for fault locating.
Port Rate-Limiting Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.
Storm ControlStorm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Support port rate limiting based on broadcast, multicast, and unknown unicast packets.
DHCP SnoopingDHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through. Disabled by default.

Certificaciones
EMCCE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020)
SeguridadCB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition), CE-LVD (EN 62368-1: 2014+A11: 2017)
QuímicaCE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)

General

Carcasa

Metal material

Peso neto

0.4 kg (0.8 lb)

Peso bruto

1.0 kg (2.2 lb)

Dimensiones (W x H x D)

158.00 mm × 101.20 mm × 31.60 mm (6.20'' × 3.90'' × 1.20'')

Temperatura de funcionamiento

-30 °C to 65 °C (-22 °F to 149 °F)

Temperatura de almacenamiento

-40 °C to 85 °C (-40 °F to 185 °F)

Condiciones de humedad

5% to 95% (no condensation)

Humedad relativa

5% to 95% (no condensation)

Fuente de alimentación

48VDC, 1.36A

Modo de instalación

Desk-Mounted,Rail

Max. El consumo de energía

65 W

Consumo de energía en inactivo

5 W

Surge Protection

6 kV

Parámetros de red

Puertos

4 × 10/100 Mbps PoE port,1 × Gigabit RJ45 port,1 × Gigabit fiber optical port

Tabla de direcciones MAC

2 K

Capacidad de conmutación

Whole-Device Performance: 14 Gbps Port Performance: 4.8 Gbps

Tasa de reenvío de paquetes

Whole-Device Performance: 10.42 Mpps Port Performance: 3.57 Mpps

Caché interna

1 Mbits

Fuente de alimentación PoE

PoE Standard

IEEE 802.3af,IEEE 802.3at

Pin de alimentación PoE

8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)

Puerto PoE

PoE: Ports 1 to 4

Max. Puerto de alimentación

30 W

PoE Power Budget

60 W

Función de software

Largo alcance

Ports 1 to 4: up to 300 m. Long range performance may vary depend on camera model or cable condition.

Port Isolation

Ports 1 to 4: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.

PoE Watchdog

Ports 1 to 4: auto detect and restart the cameras that do not respond.

QoS

QoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.

VLAN

VLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.

HPP

Support one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.

Loop Prevention

Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.

System Maintenance

Support device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support port mirroring for fault locating.

Port Rate-Limiting

Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.

Storm Control

Storm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Support port rate limiting based on broadcast, multicast, and unknown unicast packets.

DHCP Snooping

DHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through. Disabled by default.

Certificaciones

EMC

CE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020)

Seguridad

CB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition), CE-LVD (EN 62368-1: 2014+A11: 2017)

Química

CE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)

General

CarcasaMetal material
Peso neto0.4 kg (0.8 lb)
Peso bruto1.0 kg (2.2 lb)
Dimensiones (W x H x D)158.00 mm × 101.20 mm × 31.60 mm (6.20'' × 3.90'' × 1.20'')
Temperatura de funcionamiento-30 °C to 65 °C (-22 °F to 149 °F)
Temperatura de almacenamiento-40 °C to 85 °C (-40 °F to 185 °F)
Condiciones de humedad5% to 95% (no condensation)
Humedad relativa5% to 95% (no condensation)
Fuente de alimentación48VDC, 1.36A
Modo de instalaciónDesk-Mounted,Rail
Max. El consumo de energía65 W
Consumo de energía en inactivo5 W
Surge Protection6 kV

Parámetros de red

Puertos4 × 10/100 Mbps PoE port,1 × Gigabit RJ45 port,1 × Gigabit fiber optical port
Tabla de direcciones MAC2 K
Capacidad de conmutaciónWhole-Device Performance: 14 Gbps Port Performance: 4.8 Gbps
Tasa de reenvío de paquetesWhole-Device Performance: 10.42 Mpps Port Performance: 3.57 Mpps
Caché interna1 Mbits

Fuente de alimentación PoE

PoE StandardIEEE 802.3af,IEEE 802.3at
Pin de alimentación PoE8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
Puerto PoEPoE: Ports 1 to 4
Max. Puerto de alimentación30 W
PoE Power Budget60 W

Función de software

Largo alcancePorts 1 to 4: up to 300 m. Long range performance may vary depend on camera model or cable condition.
Port IsolationPorts 1 to 4: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
PoE WatchdogPorts 1 to 4: auto detect and restart the cameras that do not respond.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support port mirroring for fault locating.
Port Rate-Limiting Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.
Storm ControlStorm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Support port rate limiting based on broadcast, multicast, and unknown unicast packets.
DHCP SnoopingDHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through. Disabled by default.

Certificaciones

EMCCE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020)
SeguridadCB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition), CE-LVD (EN 62368-1: 2014+A11: 2017)
QuímicaCE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)