Global

Global - English

Asia

Europe

Oceania

ANZ - English

Latin America

North America

Middle East and Africa

8 Port Fast Ethernet Smart Harsh POE Switch

Visualized topology management.
Network health monitor.
Layer 2 features: PoE watchdog, STP/RSTP, VLAN, SNMP, QoS, ERPS, etc.
-30°C to 65°C wide temperature range in harsh environment.

View Less

Data Sheet

Available models:

DS-3T1310P-SI/HS

Specifikace
Resources
Příslušenství

Data Sheet

Všeobecné
KrytMetal material
Čistá hmotnost0.6 kg (1.3 lb)
Celková hmotnost1.2 kg (2.6 lb)
Rozměry (Š × V × H)197.00 mm × 114.20 mm × 42.20 mm (7.70'' × 4.40'' × 1.60'')
Provozní teplota-30 °C to 65 °C (-22 °F to 149 °F)
Skladovací teplota-40 °C to 85 °C (-40 °F to 185 °F)
Provozní vlhkost5% to 95% (no condensation)
Relative Humidity5% to 95% (no condensation)
Zdroj napájení48VDC, 2.5A
Režim instalaceDesk-Mounted,Rail
Max. Spotřeba energie120 W
Spotřeba energie v nečinnosti10 W
Surge Protection6 kV

Síťové parametry
Přístavy8 × 10/100 Mbps PoE port,1 × Gigabit RJ45 port,1 × Gigabit fiber optical port
Tabulka adres MAC16 K
Spínací kapacitaWhole-Device Performance: 9.2 Gbps Port Performance: 5.6 Gbps
Rychlost předávání paketůWhole-Device Performance: 6.84 Mpps Port Performance: 4.17 Mpps
Interní mezipaměť4 Mbits

Napájení PoE
PoE StandardIEEE 802.3af,IEEE 802.3at
PoE napájecí kolík8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE PortPoE: Ports 1 to 8
Max. Napájení portu30 W
Rozpočet napájení PoE110 W

Funkce softwaru
Dlouhý dosahPorts 1 to 8: up to 300 m. Long range performance may vary depend on camera model or cable condition.
Port IsolationPorts 1 to 8: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
PoE WatchdogPorts 1 to 8: auto detect and restart the cameras that do not respond.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
Link AggregationLink aggregation is used to aggregate multiple physical ports to form a logical port for load balancing, bandwidth expansion, and port protection. Support static link aggregation. Support 1 aggregation group(s).
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support port mirroring for fault locating.
Storm ControlStorm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Support port rate limiting based on broadcast, multicast, and unknown unicast packets.
DHCP SnoopingDHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through. Disabled by default.
Port Rate-Limiting Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.

Schválení
EMCCE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020),IC (ICES-003: Issue 7:2020)
BezpečnostCB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition)), CE-LVD (EN 62368-1: 2014+A11: 2017)
ChemieCE-RoHS (2011/65/EU),WEEE (2012/19/EU),Reach (Regulation (EC) No.1907/2006)

Všeobecné

Kryt

Metal material

Čistá hmotnost

0.6 kg (1.3 lb)

Celková hmotnost

1.2 kg (2.6 lb)

Rozměry (Š × V × H)

197.00 mm × 114.20 mm × 42.20 mm (7.70'' × 4.40'' × 1.60'')

Provozní teplota

-30 °C to 65 °C (-22 °F to 149 °F)

Skladovací teplota

-40 °C to 85 °C (-40 °F to 185 °F)

Provozní vlhkost

5% to 95% (no condensation)

Relative Humidity

5% to 95% (no condensation)

Zdroj napájení

48VDC, 2.5A

Režim instalace

Desk-Mounted,Rail

Max. Spotřeba energie

120 W

Spotřeba energie v nečinnosti

10 W

Surge Protection

6 kV

Síťové parametry

Přístavy

8 × 10/100 Mbps PoE port,1 × Gigabit RJ45 port,1 × Gigabit fiber optical port

Tabulka adres MAC

16 K

Spínací kapacita

Whole-Device Performance: 9.2 Gbps Port Performance: 5.6 Gbps

Rychlost předávání paketů

Whole-Device Performance: 6.84 Mpps Port Performance: 4.17 Mpps

Interní mezipaměť

4 Mbits

Napájení PoE

PoE Standard

IEEE 802.3af,IEEE 802.3at

PoE napájecí kolík

8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)

PoE Port

PoE: Ports 1 to 8

Max. Napájení portu

30 W

Rozpočet napájení PoE

110 W

Funkce softwaru

Dlouhý dosah

Ports 1 to 8: up to 300 m. Long range performance may vary depend on camera model or cable condition.

Port Isolation

Ports 1 to 8: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.

PoE Watchdog

Ports 1 to 8: auto detect and restart the cameras that do not respond.

QoS

QoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.

Link Aggregation

Link aggregation is used to aggregate multiple physical ports to form a logical port for load balancing, bandwidth expansion, and port protection. Support static link aggregation. Support 1 aggregation group(s).

VLAN

VLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.

HPP

Support one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.

Loop Prevention

Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.

System Maintenance

Support device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support port mirroring for fault locating.

Storm Control

Storm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Support port rate limiting based on broadcast, multicast, and unknown unicast packets.

DHCP Snooping

DHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through. Disabled by default.

Port Rate-Limiting

Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.

Schválení

EMC

CE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020),IC (ICES-003: Issue 7:2020)

Bezpečnost

CB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition)), CE-LVD (EN 62368-1: 2014+A11: 2017)

Chemie

CE-RoHS (2011/65/EU),WEEE (2012/19/EU),Reach (Regulation (EC) No.1907/2006)

Všeobecné

KrytMetal material
Čistá hmotnost0.6 kg (1.3 lb)
Celková hmotnost1.2 kg (2.6 lb)
Rozměry (Š × V × H)197.00 mm × 114.20 mm × 42.20 mm (7.70'' × 4.40'' × 1.60'')
Provozní teplota-30 °C to 65 °C (-22 °F to 149 °F)
Skladovací teplota-40 °C to 85 °C (-40 °F to 185 °F)
Provozní vlhkost5% to 95% (no condensation)
Relative Humidity5% to 95% (no condensation)
Zdroj napájení48VDC, 2.5A
Režim instalaceDesk-Mounted,Rail
Max. Spotřeba energie120 W
Spotřeba energie v nečinnosti10 W
Surge Protection6 kV

Síťové parametry

Přístavy8 × 10/100 Mbps PoE port,1 × Gigabit RJ45 port,1 × Gigabit fiber optical port
Tabulka adres MAC16 K
Spínací kapacitaWhole-Device Performance: 9.2 Gbps Port Performance: 5.6 Gbps
Rychlost předávání paketůWhole-Device Performance: 6.84 Mpps Port Performance: 4.17 Mpps
Interní mezipaměť4 Mbits

Napájení PoE

PoE StandardIEEE 802.3af,IEEE 802.3at
PoE napájecí kolík8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE PortPoE: Ports 1 to 8
Max. Napájení portu30 W
Rozpočet napájení PoE110 W

Funkce softwaru

Dlouhý dosahPorts 1 to 8: up to 300 m. Long range performance may vary depend on camera model or cable condition.
Port IsolationPorts 1 to 8: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
PoE WatchdogPorts 1 to 8: auto detect and restart the cameras that do not respond.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
Link AggregationLink aggregation is used to aggregate multiple physical ports to form a logical port for load balancing, bandwidth expansion, and port protection. Support static link aggregation. Support 1 aggregation group(s).
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support port mirroring for fault locating.
Storm ControlStorm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Support port rate limiting based on broadcast, multicast, and unknown unicast packets.
DHCP SnoopingDHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through. Disabled by default.
Port Rate-Limiting Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.

Schválení

EMCCE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020),IC (ICES-003: Issue 7:2020)
BezpečnostCB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition)), CE-LVD (EN 62368-1: 2014+A11: 2017)
ChemieCE-RoHS (2011/65/EU),WEEE (2012/19/EU),Reach (Regulation (EC) No.1907/2006)