Canada - FR
X
image

16 Port Fast Ethernet Smart POE Switch

  • 16 × 10/100 Mbps PoE ports, 2 × Gigabit combos.
  • Total PoE Power Budget 230 W
  • Support 802.1Q VLAN
  • Support PoE watchdog to detect and restart the cameras that do not respond
  • Support STP/RSTP Loop prevention
  • Support cable detection to locate failure
  • Up to 300 m Long Range PoE Transmission
  • 6 kV Surge Protection
View Less
View more
Data Sheet
Sales Inquiry
DS-3E1318P-EI
Data Sheet

Specification

  • General
  • ShellMetal material
  • Net Weight2.59 kg (5.71 lb)
  • Gross Weight3.68 kg (8.11 lb)
  • Dimensions (W × H × D)440.00 mm × 44.00 mm × 220.80 mm (17.32'' × 1.73'' × 8.69'')
  • Operating Temperature0 °C to 45 °C (0 °F to 113 °F)
  • Storage Temperature-40 °C to 85 °C (-40 °F to 185 °F)
  • Operating Humidity5% to 95% (no condensation)
  • Relative Humidity5% to 95% (no condensation)
  • Alimentation 100-240 VAC, 50/60 Hz, Max. 4 A
  • Installation ModeRack (equipped with mounting ears)
  • Max. Power Consumption250 W
  • Power Consumption in Idle20 W
  • Surge Protection6 kV
  • Network Parameters
  • Ports16 × 10/100 Mbps PoE port,2 × Gigabit combo
  • MAC Address Table16 K
  • Switching CapacityWhole-Device Performance: 9.2 Gbps Port Performance: 7.2 Gbps
  • Packet Forwarding RateWhole-Device Performance: 6.84 Mpps Port Performance: 5.36 Mpps
  • Internal Cache4 Mbits
  • PoE Power Supply
  • PoE StandardIEEE 802.3af,IEEE 802.3at
  • PoE Power Pin8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
  • PoE PortPoE: Ports 1 to 16
  • Max. Port Power30 W
  • PoE Power Budget230 W
  • Software Function
  • Long RangePorts 1 to 16: up to 300 m. Long range performance may vary depend on camera model or cable condition.
  • VIP PortPorts 1 to 8: data on VIP ports is preferentially forwarded when bandwidth resources are insufficient.
  • Port IsolationPorts 1 to 16: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
  • PoE WatchdogPorts 1 to 16: auto detect and restart the cameras that do not respond.
  • Link AggregationLink aggregation is used to aggregate multiple physical ports to form a logical port for load balancing, bandwidth expansion, and port protection. Support static link aggregation. Support 1 aggregation groups.
  • Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
  • VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
  • HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
  • System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support port mirroring for fault locating.
  • Approval
  • EMCCE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020),IC (ICES-003: Issue 7:2020),RCM (AS/NZS CISPR 32: 2015)
  • SafetyCB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition)), CE-LVD (EN 62368-1: 2014+A11: 2017)
  • ChemistryCE-RoHS (2011/65/EU),WEEE (2012/19/EU),Reach (Regulation (EC) No.1907/2006)
*Product performance is based on testing in a controlled environment. Your results may vary due to several external and environmental factors.

Specification

General
Shell
Metal material
Net Weight
2.59 kg (5.71 lb)
Gross Weight
3.68 kg (8.11 lb)
Dimensions (W × H × D)
440.00 mm × 44.00 mm × 220.80 mm (17.32'' × 1.73'' × 8.69'')
Operating Temperature
0 °C to 45 °C (0 °F to 113 °F)
Storage Temperature
-40 °C to 85 °C (-40 °F to 185 °F)
Operating Humidity
5% to 95% (no condensation)
Relative Humidity
5% to 95% (no condensation)
Alimentation
100-240 VAC, 50/60 Hz, Max. 4 A
Installation Mode
Rack (equipped with mounting ears)
Max. Power Consumption
250 W
Power Consumption in Idle
20 W
Surge Protection
6 kV
Network Parameters
Ports
16 × 10/100 Mbps PoE port,2 × Gigabit combo
MAC Address Table
16 K
Switching Capacity
Whole-Device Performance: 9.2 Gbps Port Performance: 7.2 Gbps
Packet Forwarding Rate
Whole-Device Performance: 6.84 Mpps Port Performance: 5.36 Mpps
Internal Cache
4 Mbits
PoE Power Supply
PoE Standard
IEEE 802.3af,IEEE 802.3at
PoE Power Pin
8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE Port
PoE: Ports 1 to 16
Max. Port Power
30 W
PoE Power Budget
230 W
Software Function
Long Range
Ports 1 to 16: up to 300 m. Long range performance may vary depend on camera model or cable condition.
VIP Port
Ports 1 to 8: data on VIP ports is preferentially forwarded when bandwidth resources are insufficient.
Port Isolation
Ports 1 to 16: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
PoE Watchdog
Ports 1 to 16: auto detect and restart the cameras that do not respond.
Link Aggregation
Link aggregation is used to aggregate multiple physical ports to form a logical port for load balancing, bandwidth expansion, and port protection. Support static link aggregation. Support 1 aggregation groups.
Loop Prevention
Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
VLAN
VLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
HPP
Support one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
System Maintenance
Support device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support port mirroring for fault locating.
Approval
EMC
CE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020),IC (ICES-003: Issue 7:2020),RCM (AS/NZS CISPR 32: 2015)
Safety
CB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition)), CE-LVD (EN 62368-1: 2014+A11: 2017)
Chemistry
CE-RoHS (2011/65/EU),WEEE (2012/19/EU),Reach (Regulation (EC) No.1907/2006)
For better user experience, we highly recommend you to update your device to the latest firmware asap.
Specification
General
  • ShellMetal material
  • Net Weight2.59 kg (5.71 lb)
  • Gross Weight3.68 kg (8.11 lb)
  • Dimensions (W × H × D)440.00 mm × 44.00 mm × 220.80 mm (17.32'' × 1.73'' × 8.69'')
  • Operating Temperature0 °C to 45 °C (0 °F to 113 °F)
  • Storage Temperature-40 °C to 85 °C (-40 °F to 185 °F)
  • Operating Humidity5% to 95% (no condensation)
  • Relative Humidity5% to 95% (no condensation)
  • Alimentation 100-240 VAC, 50/60 Hz, Max. 4 A
  • Installation ModeRack (equipped with mounting ears)
  • Max. Power Consumption250 W
  • Power Consumption in Idle20 W
  • Surge Protection6 kV
Network Parameters
  • Ports16 × 10/100 Mbps PoE port,2 × Gigabit combo
  • MAC Address Table16 K
  • Switching CapacityWhole-Device Performance: 9.2 Gbps Port Performance: 7.2 Gbps
  • Packet Forwarding RateWhole-Device Performance: 6.84 Mpps Port Performance: 5.36 Mpps
  • Internal Cache4 Mbits
PoE Power Supply
  • PoE StandardIEEE 802.3af,IEEE 802.3at
  • PoE Power Pin8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
  • PoE PortPoE: Ports 1 to 16
  • Max. Port Power30 W
  • PoE Power Budget230 W
Software Function
  • Long RangePorts 1 to 16: up to 300 m. Long range performance may vary depend on camera model or cable condition.
  • VIP PortPorts 1 to 8: data on VIP ports is preferentially forwarded when bandwidth resources are insufficient.
  • Port IsolationPorts 1 to 16: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
  • PoE WatchdogPorts 1 to 16: auto detect and restart the cameras that do not respond.
  • Link AggregationLink aggregation is used to aggregate multiple physical ports to form a logical port for load balancing, bandwidth expansion, and port protection. Support static link aggregation. Support 1 aggregation groups.
  • Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
  • VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
  • HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
  • System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support port mirroring for fault locating.
Approval
  • EMCCE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020),IC (ICES-003: Issue 7:2020),RCM (AS/NZS CISPR 32: 2015)
  • SafetyCB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition)), CE-LVD (EN 62368-1: 2014+A11: 2017)
  • ChemistryCE-RoHS (2011/65/EU),WEEE (2012/19/EU),Reach (Regulation (EC) No.1907/2006)
*Product performance is based on testing in a controlled environment. Your results may vary due to several external and environmental factors.

Resources

Hikvision.com uses strictly necessary cookies and related technologies to enable the website to function. With your consent, we would also like to use cookies to observe and analyse traffic levels and other metrics / show you targeted advertising / show you advertising on the basis of your location / tailor our website's content. For more information on cookie practices please refer to our cookie policy.

 

Manage cookies Accept All
Accept All Manage cookies
contact us
Contact Sales
Technical Support
Online Service
Subscribe Newsletter
Where to Buy
Contactez-Nous

Get a better browsing experience

You are using a web browser we don’t support. Please try one of the following options to have a better experience of our web content.