Global

Global - English

Asia

Europe

Oceania

ANZ - English

Latin America

North America

Middle East and Africa

EOL

8 Port Fast Ethernet Smart POE Switch

8 × 100 Mbps PoE RJ45 port, 2 × gigabit combo.
IEEE 802.3at/af standard for PoE ports.
Network topology management, alarm push, network health monitor.
6 KV surge protection for PoE ports.
AF/AT camera can reach up to 300 m in extend mode.

View Less

Data Sheet

Available models:

DS-3E1310P-SI

EOL

Specification
Resources
Accessories

Data Sheet

General
ShellMetal material
Net Weight1.72 kg (3.79 lb)
Gross Weight2.20 kg (4.85 lb)
Dimensions (W × H × D)266.00 mm × 44.50 mm × 220.80 mm (10.47'' × 1.75'' × 8.69'')
Operating Temperature0 °C to 45 °C (0 °F to 113 °F)
Storage Temperature-40 °C to 85 °C (-40 °F to 185 °F)
Operating Humidity5% to 95% (no condensation)
Relative Humidity5% to 95% (no condensation)
Power Supply100-240 VAC, 50/60 Hz, Max. 1.5 A
Installation ModeRack (equipped with mounting ears)
Max. Power Consumption150 W
Power Consumption in Idle5 W
Surge Protection6 KV

Network Parameters
Porti8 × 10/100 Mbps PoE port,2 × Gigabit combo
MAC Address Table16 K
Switching Capacity9.2 Gbps
Packet Forwarding Rate6.84 Mpps
Internal Cache4 Mbits

PoE Power Supply
PoE StandardIEEE 802.3af,IEEE 802.3at
PoE Power Pin8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE PortPoE: Ports 1 to 8
Max. Port Power30 W
PoE Power Budget125 W

Software Function
Long RangePorts 1 to 8: up to 300 m. Long range performance may vary depend on camera model or cable condition.
Port IsolationPorts 1 to 8: port isolation mode to improve network security. Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
PoE WatchdogPorts 1 to 8: auto detect and restart the cameras that do not respond.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support remote management via Hik-Partner Pro. Support 802.1ab LLDP for peer device discovery. Support SNMP v1/v2c for third-party management platform access. Support port mirroring for fault locating.

Approval
EMCFCC (47 CFR Part 15, Subpart B); CE-EMC (EN 55032: 2015, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011 +A1: 2014, EN 55035: 2017); IC (ICES-003: Issue 6); RCM (ASNZS CISPR 32: 2015)
SafetyUL (UL 60950-1); CB (IEC 60950-1:2005, AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition); CE-LVD (EN 60950-1: 2006 + A11: 2009 +A1: 2010+A12: 2011+A2: 2013, EN 62368-1: 2014+A11: 2017)
ChemistryCE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)

General

Shell

Metal material

Net Weight

1.72 kg (3.79 lb)

Gross Weight

2.20 kg (4.85 lb)

Dimensions (W × H × D)

266.00 mm × 44.50 mm × 220.80 mm (10.47'' × 1.75'' × 8.69'')

Operating Temperature

0 °C to 45 °C (0 °F to 113 °F)

Storage Temperature

-40 °C to 85 °C (-40 °F to 185 °F)

Operating Humidity

5% to 95% (no condensation)

Relative Humidity

5% to 95% (no condensation)

Power Supply

100-240 VAC, 50/60 Hz, Max. 1.5 A

Installation Mode

Rack (equipped with mounting ears)

Max. Power Consumption

150 W

Power Consumption in Idle

5 W

Surge Protection

6 KV

Network Parameters

Porti

8 × 10/100 Mbps PoE port,2 × Gigabit combo

MAC Address Table

16 K

Switching Capacity

9.2 Gbps

Packet Forwarding Rate

6.84 Mpps

Internal Cache

4 Mbits

PoE Power Supply

PoE Standard

IEEE 802.3af,IEEE 802.3at

PoE Power Pin

8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)

PoE Port

PoE: Ports 1 to 8

Max. Port Power

30 W

PoE Power Budget

125 W

Software Function

Long Range

Ports 1 to 8: up to 300 m. Long range performance may vary depend on camera model or cable condition.

Port Isolation

Ports 1 to 8: port isolation mode to improve network security. Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.

PoE Watchdog

Ports 1 to 8: auto detect and restart the cameras that do not respond.

QoS

QoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.

Loop Prevention

Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.

VLAN

VLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.

HPP

Support one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.

System Maintenance

Support device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support remote management via Hik-Partner Pro. Support 802.1ab LLDP for peer device discovery. Support SNMP v1/v2c for third-party management platform access. Support port mirroring for fault locating.

Approval

EMC

FCC (47 CFR Part 15, Subpart B); CE-EMC (EN 55032: 2015, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011 +A1: 2014, EN 55035: 2017); IC (ICES-003: Issue 6); RCM (ASNZS CISPR 32: 2015)

Safety

UL (UL 60950-1); CB (IEC 60950-1:2005, AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition); CE-LVD (EN 60950-1: 2006 + A11: 2009 +A1: 2010+A12: 2011+A2: 2013, EN 62368-1: 2014+A11: 2017)

Chemistry

CE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)

General

ShellMetal material
Net Weight1.72 kg (3.79 lb)
Gross Weight2.20 kg (4.85 lb)
Dimensions (W × H × D)266.00 mm × 44.50 mm × 220.80 mm (10.47'' × 1.75'' × 8.69'')
Operating Temperature0 °C to 45 °C (0 °F to 113 °F)
Storage Temperature-40 °C to 85 °C (-40 °F to 185 °F)
Operating Humidity5% to 95% (no condensation)
Relative Humidity5% to 95% (no condensation)
Power Supply100-240 VAC, 50/60 Hz, Max. 1.5 A
Installation ModeRack (equipped with mounting ears)
Max. Power Consumption150 W
Power Consumption in Idle5 W
Surge Protection6 KV

Network Parameters

Porti8 × 10/100 Mbps PoE port,2 × Gigabit combo
MAC Address Table16 K
Switching Capacity9.2 Gbps
Packet Forwarding Rate6.84 Mpps
Internal Cache4 Mbits

PoE Power Supply

PoE StandardIEEE 802.3af,IEEE 802.3at
PoE Power Pin8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE PortPoE: Ports 1 to 8
Max. Port Power30 W
PoE Power Budget125 W

Software Function

Long RangePorts 1 to 8: up to 300 m. Long range performance may vary depend on camera model or cable condition.
Port IsolationPorts 1 to 8: port isolation mode to improve network security. Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
PoE WatchdogPorts 1 to 8: auto detect and restart the cameras that do not respond.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support remote management via Hik-Partner Pro. Support 802.1ab LLDP for peer device discovery. Support SNMP v1/v2c for third-party management platform access. Support port mirroring for fault locating.

Approval

EMCFCC (47 CFR Part 15, Subpart B); CE-EMC (EN 55032: 2015, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011 +A1: 2014, EN 55035: 2017); IC (ICES-003: Issue 6); RCM (ASNZS CISPR 32: 2015)
SafetyUL (UL 60950-1); CB (IEC 60950-1:2005, AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition); CE-LVD (EN 60950-1: 2006 + A11: 2009 +A1: 2010+A12: 2011+A2: 2013, EN 62368-1: 2014+A11: 2017)
ChemistryCE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)