Global

Global - English

Asia

Europe

Oceania

ANZ - English

Latin America

North America

Middle East and Africa

DS-3E1310HP-EI

8 Port Fast Ethernet Smart POE Switch

8 × 100 Mbps PoE RJ45 ports, 2 × gigabit network RJ45 ports
IEEE 802.3at/af/bt standard for PoE ports
Network topology management, and alarm push
6 KV surge protection for PoE ports
Up to 300 m long-range transmission
AF/AT camera can reach up to 300 m in extend mode

View Less

Available models:

DS-3E1310HP-EI

General
ShellMetal material, IP40
Net Weight0.550 kg (1.21 lb)
Gross Weight0.950 kg (2.09 lb)
Dimensions (W × H × D)217.6 mm × 27.8 mm × 103.35 mm (8.56" × 1.09" × 4.06")
Operating Temperature0°C to 40°C (0°F to 104°F)
Storage Temperature-40°C to 85°C (-40°F to 185°F)
Operating Humidity5% to 95% (no condensation)
Relative Humidity5% to 95% (no condensation)
Power Supply54 VDC, 2.22 A
Installation ModeDesk-Mounted; Wall-Mounted;
Max. Power Consumption120 W
Power Consumption in Idle4 W
Surge Protection6 KV

Network Parameters
Ports8 × 10/100 Mbps PoE port,2 × Gigabit RJ45 port
MAC Address Table16 K
Switching Capacity9.2 Gbps
Packet Forwarding Rate6.84 Mpps
Internal Cache4 Mbits

PoE Power Supply
PoE StandardIEEE 802.3af,IEEE 802.3at,IEEE 802.3bt
PoE Power Pin8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE PortHi-PoE: Ports 1 to 2,PoE: Ports 3 to 8
Max. Port Power90 W
PoE Power Budget110 W

Software Function
Long RangePorts 1 to 8: up to 300 m. Long range performance may vary depend on camera model or cable condition.
PoE WatchdogPorts 1 to 8: auto detect and restart the cameras that do not respond.
VIP Port/
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
Port Isolation/
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support SNMP v1/v2c for third-party management platform access. Support port mirroring for fault locating.
Link Aggregation/
Storm ControlStorm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Supports port rate limiting based on broadcast, multicast, and unknown unicast packets.
DHCP SnoopingDHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through Off by default.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. VLAN.
Port Rate-Limiting Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.
IGMP Snooping/
ACL/
IPSG/

Approval
EMCFCC (47 CFR Part 15, Subpart B); CE-EMC (EN 55032: 2015, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011 +A1: 2014, EN 55035: 2017); IC (ICES-003: Issue 6); RCM (ASNZS CISPR 32: 2015)
SafetyUL (UL 60950-1); CB (IEC 60950-1:2005, AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition); CE-LVD (EN 60950-1: 2006 + A11: 2009 +A1: 2010+A12: 2011+A2: 2013, EN 62368-1: 2014+A11: 2017)
ChemistryCE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)

Specification

General

Shell

Metal material, IP40

Net Weight

0.550 kg (1.21 lb)

Gross Weight

0.950 kg (2.09 lb)

Dimensions (W × H × D)

217.6 mm × 27.8 mm × 103.35 mm (8.56" × 1.09" × 4.06")

Operating Temperature

0°C to 40°C (0°F to 104°F)

Storage Temperature

-40°C to 85°C (-40°F to 185°F)

Operating Humidity

5% to 95% (no condensation)

Relative Humidity

5% to 95% (no condensation)

Power Supply

54 VDC, 2.22 A

Installation Mode

Desk-Mounted; Wall-Mounted;

Max. Power Consumption

120 W

Power Consumption in Idle

4 W

Surge Protection

6 KV

Network Parameters

Ports

8 × 10/100 Mbps PoE port,2 × Gigabit RJ45 port

MAC Address Table

16 K

Switching Capacity

9.2 Gbps

Packet Forwarding Rate

6.84 Mpps

Internal Cache

4 Mbits

PoE Power Supply

PoE Standard

IEEE 802.3af,IEEE 802.3at,IEEE 802.3bt

PoE Power Pin

8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)

PoE Port

Hi-PoE: Ports 1 to 2,PoE: Ports 3 to 8

Max. Port Power

90 W

PoE Power Budget

110 W

Software Function

Long Range

Ports 1 to 8: up to 300 m. Long range performance may vary depend on camera model or cable condition.

PoE Watchdog

Ports 1 to 8: auto detect and restart the cameras that do not respond.

VIP Port

HPP

Support one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.

Port Isolation

System Maintenance

Support device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support SNMP v1/v2c for third-party management platform access. Support port mirroring for fault locating.

Link Aggregation

Storm Control

Storm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Supports port rate limiting based on broadcast, multicast, and unknown unicast packets.

DHCP Snooping

DHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through Off by default.

QoS

QoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.

Loop Prevention

Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.

VLAN

VLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. VLAN.

Port Rate-Limiting

Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.

IGMP Snooping

ACL

IPSG

Approval

EMC

FCC (47 CFR Part 15, Subpart B); CE-EMC (EN 55032: 2015, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011 +A1: 2014, EN 55035: 2017); IC (ICES-003: Issue 6); RCM (ASNZS CISPR 32: 2015)

Safety

UL (UL 60950-1); CB (IEC 60950-1:2005, AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition); CE-LVD (EN 60950-1: 2006 + A11: 2009 +A1: 2010+A12: 2011+A2: 2013, EN 62368-1: 2014+A11: 2017)

Chemistry

CE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)

General

ShellMetal material, IP40
Net Weight0.550 kg (1.21 lb)
Gross Weight0.950 kg (2.09 lb)
Dimensions (W × H × D)217.6 mm × 27.8 mm × 103.35 mm (8.56" × 1.09" × 4.06")
Operating Temperature0°C to 40°C (0°F to 104°F)
Storage Temperature-40°C to 85°C (-40°F to 185°F)
Operating Humidity5% to 95% (no condensation)
Relative Humidity5% to 95% (no condensation)
Power Supply54 VDC, 2.22 A
Installation ModeDesk-Mounted; Wall-Mounted;
Max. Power Consumption120 W
Power Consumption in Idle4 W
Surge Protection6 KV

Network Parameters

Ports8 × 10/100 Mbps PoE port,2 × Gigabit RJ45 port
MAC Address Table16 K
Switching Capacity9.2 Gbps
Packet Forwarding Rate6.84 Mpps
Internal Cache4 Mbits

PoE Power Supply

PoE StandardIEEE 802.3af,IEEE 802.3at,IEEE 802.3bt
PoE Power Pin8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE PortHi-PoE: Ports 1 to 2,PoE: Ports 3 to 8
Max. Port Power90 W
PoE Power Budget110 W

Software Function

Long RangePorts 1 to 8: up to 300 m. Long range performance may vary depend on camera model or cable condition.
PoE WatchdogPorts 1 to 8: auto detect and restart the cameras that do not respond.
VIP Port/
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
Port Isolation/
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support SNMP v1/v2c for third-party management platform access. Support port mirroring for fault locating.
Link Aggregation/
Storm ControlStorm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Supports port rate limiting based on broadcast, multicast, and unknown unicast packets.
DHCP SnoopingDHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through Off by default.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP.
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. VLAN.
Port Rate-Limiting Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.
IGMP Snooping/
ACL/
IPSG/

Approval

EMCFCC (47 CFR Part 15, Subpart B); CE-EMC (EN 55032: 2015, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011 +A1: 2014, EN 55035: 2017); IC (ICES-003: Issue 6); RCM (ASNZS CISPR 32: 2015)
SafetyUL (UL 60950-1); CB (IEC 60950-1:2005, AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition); CE-LVD (EN 60950-1: 2006 + A11: 2009 +A1: 2010+A12: 2011+A2: 2013, EN 62368-1: 2014+A11: 2017)
ChemistryCE-RoHS (201165EU); WEEE (201219EU); Reach (Regulation (EC) No.19072006)