Global

Global - English

Asia

Europe

Oceania

ANZ - English

Latin America

North America

Middle East and Africa

28 Port Aggregation Switch

24 x gigabit RJ45 ports,4 x gigabit fiber optical port
Support DHCP snooping
Support 802.1Q VLAN
Support ACL List
Support STP/ERPS loop prevention, storm control
Support ARP Anti-Spoofing
Support SNMP, QoS
6 kV Surge Protection

View Less

Data Sheet

Available models:

DS-3E1528-SI-24T4F

Especificación
Resources
Accesorios

Data Sheet

General
CarcasaMetal material
Peso neto2.3 kg (5.07 lb)
Peso bruto2.82 kg (6.22 lb)
Dimensiones (W x H x D)440 mm × 44 mm × 220.8 mm (17.32”× 1.73”× 8.69'')
Temperatura de funcionamiento0°C to 45°C (0 °F to 113 °F)
Temperatura de almacenamiento-40 °C to 85 °C (-40 °F to 185 °F)
Condiciones de humedad5% to 95% (no condensation)
Humedad relativa5% to 95% (no condensation)
Fuente de alimentación100-240 V,50/60 Hz,0.7 A Max
Modo de instalaciónRack (equipped with mounting ears)
Max. El consumo de energía20 W
Consumo de energía en inactivo5 W
Surge Protection6 kV

Parámetros de red
Puertos24 × gigabit RJ45 port, and 4 × gigabit fiber optical port
Tabla de direcciones MAC8 K
Capacidad de conmutación56 Gbps
Tasa de reenvío de paquetes41.66 Mpps
Caché interna4.1 Mbits

Fuente de alimentación PoE
PoE Standard/
Pin de alimentación PoE/
Puerto PoE/
Max. Puerto de alimentación/

Función de software
Port IsolationPorts 1 to 28: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
Link AggregationLink aggregation is used to aggregate multiple physical ports to form a logical port for load balancing, bandwidth expansion, and port protection. Support static link aggregation. Support 8 aggregation groups.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP.
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support SNMP v1/v2c for third-party management platform access. Support port mirroring for fault locating.
Port Rate-Limiting Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.
Storm ControlStorm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Support port rate limiting based on broadcast, multicast, and unknown unicast packets.
DHCP SnoopingDHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through. Disabled by default.
ACLPort security strategy. Support up to 64 ACL entries. Support up to 128 configuration rules under all ACL entries.
IPSGIPSG can control the security of port access device. Support port, MAC, IP binding. Support 256 security table entries.

Certificaciones
EMCCE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020),IC (ICES-003: Issue 7:2020),RCM (AS/NZS CISPR 32: 2015)
Seguridad CE-LVD (EN 62368-1: 2014+A11: 2017),CB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition)
QuímicaCE-RoHS (2011/65/EU); WEEE (2012/19/EU); Reach (Regulation (EC) No.1907/2006)

General

Carcasa

Metal material

Peso neto

2.3 kg (5.07 lb)

Peso bruto

2.82 kg (6.22 lb)

Dimensiones (W x H x D)

440 mm × 44 mm × 220.8 mm (17.32”× 1.73”× 8.69'')

Temperatura de funcionamiento

0°C to 45°C (0 °F to 113 °F)

Temperatura de almacenamiento

-40 °C to 85 °C (-40 °F to 185 °F)

Condiciones de humedad

5% to 95% (no condensation)

Humedad relativa

5% to 95% (no condensation)

Fuente de alimentación

100-240 V,50/60 Hz,0.7 A Max

Modo de instalación

Rack (equipped with mounting ears)

Max. El consumo de energía

20 W

Consumo de energía en inactivo

5 W

Surge Protection

6 kV

Parámetros de red

Puertos

24 × gigabit RJ45 port, and 4 × gigabit fiber optical port

Tabla de direcciones MAC

8 K

Capacidad de conmutación

56 Gbps

Tasa de reenvío de paquetes

41.66 Mpps

Caché interna

4.1 Mbits

Fuente de alimentación PoE

PoE Standard

Pin de alimentación PoE

Puerto PoE

Max. Puerto de alimentación

Función de software

Port Isolation

Ports 1 to 28: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.

Link Aggregation

Link aggregation is used to aggregate multiple physical ports to form a logical port for load balancing, bandwidth expansion, and port protection. Support static link aggregation. Support 8 aggregation groups.

QoS

QoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.

Loop Prevention

Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP.

VLAN

VLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.

HPP

Support one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.

System Maintenance

Support device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support SNMP v1/v2c for third-party management platform access. Support port mirroring for fault locating.

Port Rate-Limiting

Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.

Storm Control

Storm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Support port rate limiting based on broadcast, multicast, and unknown unicast packets.

DHCP Snooping

DHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through. Disabled by default.

ACL

Port security strategy. Support up to 64 ACL entries. Support up to 128 configuration rules under all ACL entries.

IPSG

IPSG can control the security of port access device. Support port, MAC, IP binding. Support 256 security table entries.

Certificaciones

EMC

CE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020),IC (ICES-003: Issue 7:2020),RCM (AS/NZS CISPR 32: 2015)

Seguridad

CE-LVD (EN 62368-1: 2014+A11: 2017),CB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition)

Química

CE-RoHS (2011/65/EU); WEEE (2012/19/EU); Reach (Regulation (EC) No.1907/2006)

General

CarcasaMetal material
Peso neto2.3 kg (5.07 lb)
Peso bruto2.82 kg (6.22 lb)
Dimensiones (W x H x D)440 mm × 44 mm × 220.8 mm (17.32”× 1.73”× 8.69'')
Temperatura de funcionamiento0°C to 45°C (0 °F to 113 °F)
Temperatura de almacenamiento-40 °C to 85 °C (-40 °F to 185 °F)
Condiciones de humedad5% to 95% (no condensation)
Humedad relativa5% to 95% (no condensation)
Fuente de alimentación100-240 V,50/60 Hz,0.7 A Max
Modo de instalaciónRack (equipped with mounting ears)
Max. El consumo de energía20 W
Consumo de energía en inactivo5 W
Surge Protection6 kV

Parámetros de red

Puertos24 × gigabit RJ45 port, and 4 × gigabit fiber optical port
Tabla de direcciones MAC8 K
Capacidad de conmutación56 Gbps
Tasa de reenvío de paquetes41.66 Mpps
Caché interna4.1 Mbits

Fuente de alimentación PoE

PoE Standard/
Pin de alimentación PoE/
Puerto PoE/
Max. Puerto de alimentación/

Función de software

Port IsolationPorts 1 to 28: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
Link AggregationLink aggregation is used to aggregate multiple physical ports to form a logical port for load balancing, bandwidth expansion, and port protection. Support static link aggregation. Support 8 aggregation groups.
QoSQoS is used to allocate bandwidth to different services so as to provide end-to-end service quality assurance. Support port-based priority configuration. Support SP, WRR priority schedule mode.
Loop PreventionLoop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP.
VLANVLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN.
HPPSupport one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device.
System MaintenanceSupport device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support SNMP v1/v2c for third-party management platform access. Support port mirroring for fault locating.
Port Rate-Limiting Port rate-limiting is used for port bandwidth adjustment to prevent network congestion.
Storm ControlStorm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication. Support port rate limiting based on broadcast, multicast, and unknown unicast packets.
DHCP SnoopingDHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through. Disabled by default.
ACLPort security strategy. Support up to 64 ACL entries. Support up to 128 configuration rules under all ACL entries.
IPSGIPSG can control the security of port access device. Support port, MAC, IP binding. Support 256 security table entries.

Certificaciones

EMCCE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020),IC (ICES-003: Issue 7:2020),RCM (AS/NZS CISPR 32: 2015)
Seguridad CE-LVD (EN 62368-1: 2014+A11: 2017),CB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition)
QuímicaCE-RoHS (2011/65/EU); WEEE (2012/19/EU); Reach (Regulation (EC) No.1907/2006)