Please be aware that Hikvision products are region-specific and regionally supported. If you have purchased your Hikvision products from an online source or unauthorized distributor, they may not be compatible with the North American region’s firmware and are considered to be “gray market” product. If your camera has “CH” in the serial number, you are most likely using a “gray market” product. Updating the firmware from this site can lead to several complications in those cameras, up to and including camera failure. Restoring a “gray market” product to its original condition is a factory process and will result in a Chinese interface. As Hikvision warranty is void in this case, you must rely on the dealer for any service, support, and warranty of the “gray market” product. If you have any questions or concerns about the official status of your Hikvision distributor, please contact Hikvision USA Customer Service at csr.usa@hikvision.com.
  • Baseline Firmware_Thermal_IPHC_H1_EN_STD_5.5.0_180411 (for 21XX, 23XX, 24XX)
    • Baseline Firmware_Thermal_IPHC_H1_EN_STD_5.5.0_180411 (for 21XX, 23XX, 24XX)
    •  

      DS-2TD2136-7/10/15/25/35

      DS-2TD2136T-10/15/25

      DS-2TD2166-7/15/25/35

      DS-2TD2166T-15/25

      DS-2TD2336-50/75/100

      DS-2TD2366-50/75/100

      DS-2TD2466-25/50Y

       

  • Baseline Firmware_NVR(-I series)_En_STD_V3.3.6 150828(New)
    • Baseline Firmware_NVR(-I series)_En_STD_V3.3.6 150828(New)
    •  

      Support Models:

       

      DS-9600NI-I8, DS-7700NI-I4, DS-7600NI-I2

      Updates:

      1. Add a configuration option “Enable H.265 (For Initial Access)”, which is used for switching stream to H.265 automatically when NVR accesses IPC at first time.

      2. Change the incoming/outgoing bandwidth of DS-7600NI-I2 and DS-7700NI-I4. The incoming bandwidth of 32-ch is changed from 320Mbps to 256Mbps, and the outgoing bandwidth is changed to 256Mbps for all types.

      3. Fix some small bugs.

      4. Other updates.

  • Baseline Firmware_IPC_En_V5.3.6 151105 (2X22WD, 2X42WD)
    • Baseline Firmware_IPC_En_V5.3.6 151105 (2X22WD, 2X42WD)
    •  

      Support models:

      DS-2CD2T42WD-I3/I5/I8, DS-2CD2742FWD-I(Z)S, DS-2CD2642FWD-I(Z)S, DS-2CD2542FWD-(I)(W)(S), DS-2CD2342WD-I, DS-2CD2142FWD-I(W)(S), DS-2CD2042WD-I, DS-2CD2F42FWD-I(W)(S)

      DS-2CD2T22WD- I3/I5/I8, DS-2CD2722FWD-I(Z)S, DS-2CD2622FWD-I(Z)S, DS-2CD2522FWD-(I)(W)(S), DS-2CD2322WD-I, DS-2CD2122FWD-I(W)(S), DS-2CD2122FWD-I(W)(S) (C), DS-2CD2022WD-I, DS-2CD2F22FWD-I(W)(S)


      Updates:

      1. Optimize the image quality;

      2. H.264+ and Rotate Mode are supported simultaneously for 2MP devices;

      3. Solved defect: Image flicker when connecting to Hikvision NVR;

      4. For more details, please refer to our release notes.


      Firmware V5.3.6 Release Note.pdf


  • Baseline Firmware_NVR (76/77/86NI-E)_En_V3.4.0_150929(new)
    • Baseline Firmware_NVR (76/77/86NI-E)_En_V3.4.0_150929(new)
    •  

      Support Models:

      DS-7600NI-E1, DS-7600NI-E2, DS-7600NI-E1/N(P), DS-7600NI-E2/N(P), DS-7700NI-E4, DS-7700NI-E4/N(P),DS-8608/16/32NI-E8

       

      Updates:

      1. Password synchronized to connected Hikvision IPCs when change NVR’s password;

      2. Support H.265 video stream access, storage, remotely live view and playback;

      3. Optimize the password recovery mechanism to make it securer and more convenient;

      4. Support VCA alarm notification on ivms-4500;

      5. Reliable transmission under low-bandwidth condition;

      6. Support zooming for IPCs with motorized lens;

      7. Security enhancement and improvements;

      8. Other bug fixes.

       

  • Baseline Firmware_IPC_En_V5.3.0 150513 (2XX0)(New)
    • Baseline Firmware_IPC_En_V5.3.0 150513 (2XX0)(New)

    • Support models:

      DS-2CD2010-I, DS-2CD2110-I, DS-2CD2210-I3/I5, DS-2CD2310-I, DS-2CD2410FD-I(W), DS-2CD2810F, DS-2CD2510F, DS-2CD2610F-I(S), DS-2CD2710F-I(S), DS-2CD2220-I3/I5, DS-2CD2320-I, DS-2CD2410FD-I(W), DS-2CD2620F-I(S), DS-2CD2720F-I(S), DS-2CD2820F, DS-2CD2C10F-I(W), DS-2CD2D14WD, DS-2CD2Q10FD-IW, DS-2CD2014WD-I, DS-2CD2114WD-I, DS-2CD2520F, DS-2CD2020-I, DS-2CD2120-I, DS-2CD2420-I, DS-2CD2A10F-I, DS-2CD2512F-IB, DS-2CD1010-I, DS-2CD1110-I, DS-2CD1410FD-IW, DS-2CD2110F-I(W)(S), DS-2CD2120F-I(W)(S), DS-2CD2T10-I3(I5), DS-2CD2T20-I3(I5)


      Updates:

      1. Password creating is required before using the camera (web browser, client software and SADP software are optional);

      2. Password strength prompts(Risk,Weak, Medium, Strong) in web browser, client software and SADP software, and risk password is not permitted;

      3. Telnet access is no longer available;

      4. Lock the remote IP addresses for 30 minutes once login with wrong username or password after several times;

      5. Default IP address has been changed to 192.168.1.64;

      6. Can not be downgraded to lower firmare version;

      7. For more details, please refer to our release notes.

       

      Note: IPC with firmware V5.3.0 or above version are recommended to work with NVR V3.3.0 or above version.

       

      Firmware V5.3.0 Release Note (New).pdf


  • Baseline Firmware_NVR (DS-7116NI-SN)_En_STD_V3.0.16build150617(new)
    • Baseline Firmware_NVR (DS-7116NI-SN)_En_STD_V3.0.16build150617(new)
    •  

       Support Models:

       

      DS-7116NI-SN, DS-7116NI-SN/N, DS-7116NI-SN/P

      Updates:

      1. Password creating is required before using the NVR (Local GUI menu, web browser, client software and SADP software are optional);

      2. Password strength prompts(Risk,Weak, Medium, Strong) in NVR local GUI menu, web browser, client software and SADP software, and risk password is not permitted;

      3. Lock the remote IP addresses for 30 minutes once login with wrong username or password after several times;

      4. Can not be downgraded to lower firmare version;

      5. Fix some small bugs.

      6. Other updates.

       

  • Baseline Firmware_IPC_En_V5.3.0 150513 (2XX2)(New)
    • Baseline Firmware_IPC_En_V5.3.0 150513 (2XX2)(New)

    • Support models:
      DS-2CD2012-I, DS-2CD2032-I, DS-2CD2112-I, DS-2CD2132-I, DS-2CD2212-I3/I5, DS-2CD2232-I3/I5, DS-2CD2312-I, DS-2CD2332-I, DS-2CD2412F-I(W), DS-2CD2432F-I(W), DS-2CD2512F-I(S)(W), DS-2CD2532F-I(S), DS-2CD2612F-I(S) , DS-2CD2632F-I(S) ,DS-2CD2712F-I(S) , DS-2CD2732F-I(S) , DS-2CD2022-I, DS-2CD2112F-I(W)(S), DS-2CD2122F-I(W)(S), DS-2CD2132F-I(W)(S), DS-2CD2422F-I(W), DS-2CD2522F-I(W), DS-2CD2622F-I(S), DS-2CD2722F-I(S), DS-2CD2T12-I3(I5), DS-2CD2T22-I3(I5), DS-2CD2T32-I3(I5)


      Updates:

      1. Password creating is required before using the camera (web browser, client software and SADP software are optional);

      2. Password strength prompts(Risk,Weak, Medium, Strong) in web browser, client software and SADP software, and risk password is not permitted;

      3. Telnet access is no longer available;

      4. Lock the remote IP addresses for 30 minutes once login with wrong username or password after several times;

      5. Default IP address has been changed to 192.168.1.64;

      6. Can not be downgraded to lower firmare version;

      7. For more details, please refer to our release notes.

       

      Note: IPC with firmware V5.3.0 or above version are recommended to work with NVR V3.3.0 or above version.

       

      Firmware V5.3.0 Release Note (New).pdf

       

  • Baseline Firmware_IPC_En_V5.3.3 150630(2 Series WDR models)
    • Baseline Firmware_IPC_En_V5.3.3 150630(2 Series WDR models)
    • Support models:

      DS-2CD2022WD-I, DS-2CD2042WD-I, DS-2CD2122FWD-I(W)(S), DS-2CD2142FWD-I(W)(S), DS-2CD2322WD-I, DS-2CD2342WD-I, DS-2CD2522FWD-I(W)(S), DS-2CD2542FWD-I(W)(S), DS-2CD2622FWD-I(W)(S), DS-2CD2642FWD-I(Z)(S), DS-2CD2722FWD-I(Z)(S), DS-2CD2742FWD-I(Z)(S), DS-2F12F-I(W)(S)Z, DS-2CD2F22FWD-I(W)(S), DS-2CD2F42FWD-I(W)(S), DS-2CD2T22WD-I, DS-2CD2T42WD-I

       

      Updates:

      1. V5.3.3 build 150630 supports H.264+, Hikvision H.264+ algorithm enables lower bandwidth compared to H.264 while maintaining image quality.

      2. Support 4 languages in Web Component: English, Russian, Spanish, Portuguese

      3. Support intrusion detection and line crossing detection.

      4. -Z models support motorized zoom.

      5. All models except for DS-2CD2F12F-I(W)(S)Z support 120dB true WDR.

       

      Notice:

      H.264+ and Rotate are not supported simultaneously.

       

      Firmware V5.3.3 Release Note.pdf

       

       

  • Baseline Firmware_DVR (7224HWI-E2)_En_V3.1.4_build150430(new)
    • Baseline Firmware_DVR (7224HWI-E2)_En_V3.1.4_build150430(new)
    •  

       Support Models:

      DS-7224HWI-E2

      Updates:

      1. Password creating is required before using the DVR (Local GUI menu, web browser, client software and SADP software are optional);

      2. Password strength prompts(Risk,Weak, Medium, Strong) in DVR local GUI menu, web browser, client software and SADP software, and risk password is not permitted;

      3. Lock the remote IP addresses for 30 minutes once login with wrong username or password after several times;

      4. Can not be downgraded to lower firmare version;

      5. Other updates.

       

       

  • Baseline Firmware_DS-71_7216HGHI-Ex_ML_V3.1.6build150427(new)
    • Baseline Firmware_DS-71_7216HGHI-Ex_ML_V3.1.6build150427(new)
    •  

       

       Support Models: 

      DS-7116HGHI-E1, DS-7216HGHI-E1, DS-7216HGHI-E2

       

      Updates:

      1. Password creating is required before using the DVR (Local GUI menu, web browser, client software and SADP software are optional);

      2. Password strength prompts(Risk,Weak, Medium, Strong) in DVR local GUI menu, web browser, client software and SADP software, and risk password is not permitted;

      3. Lock the remote IP addresses for 30 minutes once login with wrong username or password after several times;

      4. Can not be downgraded to lower firmare version;

      5. Other updates.

       

  • Baseline Firmware_DS-71_7208HGHI-Ex_ML_V3.1.6build150427(new)
    • Baseline Firmware_DS-71_7208HGHI-Ex_ML_V3.1.6build150427(new)
    •  

       Support Models: 

      DS-7108HGHI-E1, DS-7208HGHI-E1, DS-7208HGHI-E2

       

      Updates:

      1. Password creating is required before using the DVR (Local GUI menu, web browser, client software and SADP software are optional);

      2. Password strength prompts(Risk,Weak, Medium, Strong) in DVR local GUI menu, web browser, client software and SADP software, and risk password is not permitted;

      3. Lock the remote IP addresses for 30 minutes once login with wrong username or password after several times;

      4. Can not be downgraded to lower firmare version;

      5. Other updates.

       

  • Baseline Firmware_DS-71_7204HGHI-E1_ML_V3.1.6build150427(new)
    • Baseline Firmware_DS-71_7204HGHI-E1_ML_V3.1.6build150427(new)
    •  

       Support Models: 

      DS-7104HGHI-E1, DS-7204HGHI-E1

       

      Updates:

      1. Password creating is required before using the DVR (Local GUI menu, web browser, client software and SADP software are optional);

      2. Password strength prompts(Risk,Weak, Medium, Strong) in DVR local GUI menu, web browser, client software and SADP software, and risk password is not permitted;

      3. Lock the remote IP addresses for 30 minutes once login with wrong username or password after several times;

      4. Can not be downgraded to lower firmare version;

      5. Other updates.

       

       

  • Baseline Firmware_NVR (DS-7100NI-SL)_En_STD_V3.0.13build150420(new)
    • Baseline Firmware_NVR (DS-7100NI-SL)_En_STD_V3.0.13build150420(new)
    •  

      Support Models:

       

      DS-7104NI-SL, DS-7108NI-SL

       

      Updates:

      1. Password creating is required before using the NVR (Local GUI menu, web browser, client software and SADP software are optional);

      2. Password strength prompts(Risk,Weak, Medium, Strong) in NVR local GUI menu, web browser, client software and SADP software, and risk password is not permitted;

      3. Lock the remote IP addresses for 30 minutes once login with wrong username or password after several times;

      4. Can not be downgraded to lower firmare version;

      5. Other updates.

  • Baseline Firmware_NVR (DS-7616NI-SN)_En_STD_V3.0.13build150420(new)
    • Baseline Firmware_NVR (DS-7616NI-SN)_En_STD_V3.0.13build150420(new)
    •  

       

       Support Models:

       

      DS-7616NI-SN, DS-7616NI-SN/N, DS-7616NI-SN/P

       

      1. Password creating is required before using the NVR (Local GUI menu, web browser, client software and SADP software are optional);

      2. Password strength prompts(Risk,Weak, Medium, Strong) in NVR local GUI menu, web browser, client software and SADP software, and risk password is not permitted;

      3. Lock the remote IP addresses for 30 minutes once login with wrong username or password after several times;

      4. Can not be downgraded to lower firmare version;

      5. Other updates.

       

       

  • Baseline Firmware_NVR (DS-7604/7608NI-SN)_En_STD_V3.0.13build150420(new)
    • Baseline Firmware_NVR (DS-7604/7608NI-SN)_En_STD_V3.0.13build150420(new)
    •  

       Support Models:

       

      DS-7604NI-SN, DS-7604NI-SN/N, DS-7604NI-SN/P, DS-7608NI-SN, DS-7608NI-SN/N, DS-7608NI-SN/P

       

      1. Password creating is required before using the NVR (Local GUI menu, web browser, client software and SADP software are optional);

      2. Password strength prompts(Risk,Weak, Medium, Strong) in NVR local GUI menu, web browser, client software and SADP software, and risk password is not permitted;

      3. Lock the remote IP addresses for 30 minutes once login with wrong username or password after several times;

      4. Can not be downgraded to lower firmare version;

      5. Other updates.